15mm Bayonet Based Lamps (Automotive); Series AUT1156, AUT1157

15mm Automotive Dual 'Filament' Index Bayonet

Brake/Turn/Tail
for 12/14 Volt Applications
AUT1157-0ER-014V $19.95ea Min. Qty. 2

RED

Replacement for:
Incandescent 1157,
2057, & European P21/5W bulbs
Base Size: 15mm
Base Type: Index Dual- Contact (DC) Bayonet
Output Colors:
Super Red 633nm
Super Yellow 595nm
Operating Voltage: 12-14VDC
Forward Current (max):
160mA
Total Light Output:
Red
(End Lumens/End Footcandles): 100
Yellow
(End Lumens/End Footcandles): 72
Number of LEDs: 24

Turn/Running Light
for 12/14 Volt Applications
AUT1157-0UY-014V $19.95ea Min. Qty. 2

YELLOW

Available in Non-Index 15mm DC Bayonet for
Tail/Brake/Turn Applications as Series AUT1157DB
Contact Factory for Full Part number.

15mm Automotive Single 'Filament' SC Bayonet

Turn Signal
for 12/14 Volt Applications
AUT1156-0UY-014V $19.95ea Min. Qty. 2

YELLOW

Replacement for: Incandescent 1156
Base Size: 15mm
Base Type: Single Contact (SC) Bayonet
Output Colors:
Super Yellow 595nm
Super Red 633nm
Operating Voltage: 12-14VDC
Forward Current (max):
160mA
Total Light Output:
(Yellow)
(End Lumens/End Footcandles): 72
(Red)
(End Lumens / End Footcandles): 100
Number of LEDs: 24

Brake
for 12/14 Volt Applications
AUT1156-0ER-014V $19.95ea Min. Qty. 2

RED

Replacement for:
Incandescent # 1156
Base Size: 15mm
Base Type: Single Contact (SC) Bayonet
Output Color:
Cool White 8000K
Operating Voltage: 12-14VDC
Forward Current (max):
120mA
Total Light Output:
(End Lumens/End Footcandles): 124
Number of LEDs: 24

Back-Up
for 12/14 Volt Applications
AUT1156-0CW-014V $28.50ea Min. Qty. 2

WHITE

Sold separately
Load Resistor AUT-RES-6-50W $6.48ea Min. Qty. 1	Inline Wiring Schematic

Load Resistor Statement:
If installing LED bulbs in your car or motorcycle causes your blinkers to blink fast or causes other electrical problems you may need to install a Load resistor to correct these problems. Since LED bulbs draw much less current then standard incandescent bulbs your electrical computer system may think that your bulbs are not working. The AUT-RES-6-50 should resolve these problems. This is a 6 Ohms 50 Watt resistor that needs to be installed in-line with your tail/blinker lights, one Load resistor (AUT-RES-6-50) is required for each tail/blinker light.

Caution, this Load resistor (AUT-RES-6-50) gets extremely hot and needs to be installed correctly. The flat surface of the AUT-RES-6-50 needs to make a good secure contact on a clean flat metal surface on your car or motorcycle. This will act as a heat sink which should keep the Load resistor (AUT-RES-6-50) cooler. Keep this Load resistor (AUT-RES-6-50) away from oil, making contact with skin, plastic, wires and combustible gases and material. LEDtronics is Not responsible for damage caused to persons or property with installation of the Load resistor (AUT-RES-6-50).

Special Notes
1) For best results, LED lamp output color should be same as Lens/ Filter color above the lamp.
2) LED Lamps shown are for most standard applications.
3) Some applications may require custom or modified configuration of the LED Lamp.
4) LED Lamps shown are for direct DC or AC voltage supply. External resistor, relays or special circuits may require special LED Lamps.